Fluke Networks FI-7000 FiberInspector™ Pro - networktesters.co.uk
Fluke Networks FI-7000 FiberInspector™ Pro - networktesters.co.uk
https://youtu.be/Ebwy6B_yq7o

Fluke Networks FI-7000 FiberInspector™ Pro - FI-7000

Regular price £2,649.00 GBP
1-second automated PASS/FAIL certification of fibre optic connector end-faces with the Fluke Networks FI-7000.
  • Automated Pass/Fail certification of fibre optic connector end-faces
  • Graphical indication of problem areas due to contamination, pits, chips, and scratches
  • Certify to industry standards - IEC 61300-3-35
  • Eliminate human subjectivity from fibre optic connector end-face measurements
  • Save fibre optic connector end-face views during certification process
  • Versiv™ modular design supports copper certification, fibre optic loss, OTDR testing and fibre end-face inspection
  • Perfect for fibre inspection

    Fibre optic connector end-face contamination is a leading cause of fibre failures. Dirt and contaminant cause insertion loss and back-reflection that inhibits optical transmission and causes havoc with transceivers. Fibre loss and OTDR testing can expose this problem, but in many cases, dirty connections make fibre testing time consuming and inaccurate.

    Since dirt can be an issue before, during, or after fibre optic certification testing, and migrate from one fibre optic connector end-face to another upon mating, both sides of any connection must always be cleaned and inspected. Further, mating contaminated fibre optic connectors can cause permanent damage as microscopic debris is crushed between end-faces in physical contact. Even factory terminated patch cords or pigtails must be inspected as protective caps do not keep fibre optic connector end-faces clean. Avoiding this common cause of failure, starts with inspecting the fibre optic connector end-face and eliminating any contamination before insertion into a bulkhead or piece of equipment.

    The FI-7000 FiberInspector Pro is a fibre optic inspection scope that allows you to inspect and certify fibre optic connector end-faces in 1 seconds so you can get the job done the first time. This fibre optic inspection scope provides automated PASS/FAIL certification take the guess work out of fibre inspection so anyone can be a fibre expert.

    Features

    • Fiber Inspection Certification
    • Graphical indication of Problem Areas
    • Store End-face Images
    • Built on the Versiv Platform
    • Versiv’s ProjX™ System
    • Taptive™ User Interface
    • LinkWare™ Live Test Results Management Service
    • LinkWare™ Management Software
    • PASS/FAIL Fiber End-face Grading
    Inspection Probe specifications  
    2M pixels Blue LED
    Light source Blue LED
    Power source Versiv mainframe
    Field of View (FOV) Horizontal: 425 µm
    Vertical: 320 µm
    Minimum detectable particle size 0.5 µm
    Dimensions Approximately 6.75 in x 1.5 in (1175 mm x 35 mm) without adapter tip
    Weight 200 g
    Temperature range Operating: 32°F to 122°F (0 °C to +50 °C)
    Storage: -4°F to +158°F (-20°C to +70°C)
    Certifications CE
       
    General specifications  
    Weight Mainframe with module and battery: 3 lbs, 5 oz (1.28 kg)
    Dimensions Mainframe with module and battery: 2.625 in x 5.25 in x 11.0 in ( 6.67 cm x 13.33 cm x 27.94 cm)
    Battery Lithium ion battery pack, 7.2 volts
    Battery life Eleven hour with Inspection probe attached
       
    Charge Time  
    Tester Off Four hours to charge from 10% to 90% capacity
    Tester On Six hours to charge from 10% to 90% capacity with the tester on
       
    Environmental specifications  
    Operating temperature* -18ºC to 45ºC
    Non-operating temperature -30ºC to 60ºC
    Operating altitude 4,000 m (13123 ft)
    3200 m (10,500 ft) with ac adapter
    Storage altitude 12,000 m
    EMC EN 61326-1
       
    * Do not keep battery at temperatures below -20°C (-4°F) or above 50°C (122°F) for periods longer than one week to maintain battery capacity.  
    Part Number Description
    FI-7000

    Contains: Versiv Mainframe, USB Fiber Inspection Video Probe with 4 tips in a box (LC, FC/SC bulkhead, 1.25 and 2.5mm universal), Blank Module to protect the mainframe’s rear connector, AC Charger, Shoulder Strap, USB Interface Cable, Versiv Open Source Software CD, Getting Started Guide, Soft Carrying Case.

    FI-7000-MPO

    Contains: Versiv Mainframe, USB Fiber Inspection Video Probe with 4 tips in a box (LC, FC/SC bulkhead, 1.25 and 2.5mm universal), MPO Fiber Inspection Adapter Tip, Quick Clean Cleaners for 1.25mm & 2.5mm ferrules and MPO connectors, Blank Module to protect the mainframe’s rear connector, AC Charger, Shoulder Strap, USB Interface Cable, Versiv Open Source Software CD, Getting Started Guide, Soft Carrying Case.